9650-0902-05-SF

R Series

Configuration Manual

The issue date for the R Series Configuration Manual (REF 9650-0902-05 Rev. C) is June, 2012.

If more than 3 years have elapsed since the issue date, contact ZOLL Medical Corporation to determine if

additional product information updates are available.

See-Thru CPR, CPR Index, CPR Dashboard, Code-Ready, and OneStep are trademarks or registered

trademarks of ZOLL Medical Corporation in the United States and/or other countries.

Masimo is a registered trademark of Masimo Corporation in the United States and/or other countries.

All other trademarks are the property of their respective owners.

0123

ZOLL Medical Corporation

269 Mill Road

Chelmsford, MA USA

01824-4105

ZOLL International Holding B.V.

Newtonweg 18

6662 PV ELST

The Netherlands

9650-0902-05 Rev. C ZOLL R Series Configuration Manual i

Table of Contents

Chapter 1 Introduction

Entering System Configuration Mode.................................................................................... 2

Printing Configuration Settings and Activity Logs.................................................................. 3

Uploading Data from a Compact Flash Card......................................................................... 6

Saving Configuration to a Compact Flash Card..................................................................... 8

Restoring Default Values ....................................................................................................... 9

Accessing and Changing Configuration Settings................................................................. 10

Leaving Configuration Mode.................................................................................................11

Chapter 2 Configuration Settings

General Settings.................................................................................................................. 14

Device Identifier ........................................................................................................... 14

Configuration Mode Passcode ..................................................................................... 16

Code Markers .............................................................................................................. 17

ECG Settings....................................................................................................................... 19

Notch Filter .................................................................................................................. 19

Display Lead on Power-Up .......................................................................................... 19

Frequency Response ................................................................................................... 19

Gain on Power Up ....................................................................................................... 20

Enable Leads Off ......................................................................................................... 20

Enable Pacer Detection ............................................................................................... 20

Audio Settings...................................................................................................................... 21

QRS Volume on Power-Up .......................................................................................... 21

Low Battery Tone ......................................................................................................... 21

Enable Corrective Voice Prompts ................................................................................ 21

Basic Defibrillation Settings ................................................................................................. 22

Defib Default to Pads ................................................................................................... 22

Basic Auto Energy Escalation ...................................................................................... 22

Retain Sync After Defib ............................................................................................... 22

Defib Ready Hold Time ................................................................................................ 23

Enable Remote Sync ................................................................................................... 23

TABLE OF CONTENTS

ii www.zoll.com 9650-0902-05 Rev. C

Advisory Defib...................................................................................................................... 24

Energy Level: Shock 1 ................................................................................................. 24

Energy Level: Shock 2 ................................................................................................. 25

Energy Level: Shock 3 ................................................................................................. 25

Ped Energy Level Shock 1 .......................................................................................... 25

Ped Energy Level Shock 2 .......................................................................................... 26

Ped Energy Level Shock 3 .......................................................................................... 26

Auto Analyze ................................................................................................................ 26

Enable Check Pulse Prompt ........................................................................................ 27

Check Patient Prompt .................................................................................................. 27

Auto Charge in Advisory Mode .................................................................................... 27

Enable Voice in Advisory Mode ................................................................................... 28

Display DO CPR Message .......................................................................................... 28

CPR Message After No Shock Advised ....................................................................... 29

CPR Message After Shock .......................................................................................... 29

Stacked Shocks ........................................................................................................... 30

Restart Analysis After CPR .......................................................................................... 30

CPR Interval ................................................................................................................ 30

CPR Settings ....................................................................................................................... 31

Enable CPR Voice Prompts ......................................................................................... 31

Enable CPR Display .................................................................................................... 31

Enable CPR Dashboard .............................................................................................. 31

Display Release Bar .................................................................................................... 32

Enable CPR Metronome .............................................................................................. 32

Target CPR Depth ....................................................................................................... 32

CPR Depth Units ......................................................................................................... 32

Display Fully Release Prompt ...................................................................................... 32

Display Filtered ECG on Trace1 .................................................................................. 33

Pace Settings....................................................................................................................... 34

Pace Rate Setting on Power-Up .................................................................................. 34

Async Softkey in Pace Mode ....................................................................................... 34

Alarms Settings.................................................................................................................... 35

Alarm Limits at Power Up ............................................................................................ 36

Alarms Active at Power Up .......................................................................................... 40

Display Settings................................................................................................................... 41

Display Time ................................................................................................................ 41

Select Trace 2 At Power Up ........................................................................................ 41

Select Trace 3 At Power Up ........................................................................................ 42

ECG Color ................................................................................................................... 42

SpO

Color .................................................................................................................. 42

CPR Color .................................................................................................................... 42

EtCO

Color ................................................................................................................. 43

NIBP Color ................................................................................................................... 43

SPO

at Power Up ....................................................................................................... 43

9650-0902-05 Rev. C ZOLL R Series Configuration Manual iii

NIBP Settings (Optional)...................................................................................................... 44

Blood Pressure Units ................................................................................................... 44

Trigger NIBP Meas on BP Alarm ................................................................................. 44

Trigger NIBP Meas on HR Alarm ................................................................................. 44

NIBP Auto Interval Default ........................................................................................... 45

Adult Initial Cuff Inflation .............................................................................................. 45

Pediatric Initial Cuff Inflation ........................................................................................ 45

Neonatal Initial Cuff Inflation ........................................................................................ 45

NIBP Patient Mode at Power Up ................................................................................. 46

NIBP Button Press & Hold ........................................................................................... 46

Enable Motion Tolerance ............................................................................................. 46

EtCO

Settings (Optional).................................................................................................... 47

Default EtCO

Units ..................................................................................................... 47

Displayed Zoom Level ................................................................................................. 47

Default EtCO

Comp Setting ....................................................................................... 47

Power Save Mode at Power Up ................................................................................... 48

EtCO

Average On Power Up ..................................................................................... 48

Printer & Report Settings..................................................................................................... 49

Set Report Restart Delays ........................................................................................... 49

Auto Generate Strips ................................................................................................... 49

Print 3 Leads When Leads Sel. ................................................................................... 49

Readiness Test Settings ...................................................................................................... 50

Automatic Readiness Test ........................................................................................... 50

Readiness Test Time ................................................................................................... 50

Print Readiness Test Results ...................................................................................... 50

Enable Readiness Test Audible Alert (Future Use) ..................................................... 51

One Step Padz Installed .............................................................................................. 51

AED Mode ........................................................................................................................... 52

Display ECG in AED Mode .......................................................................................... 52

Display HR in AED Mode ............................................................................................. 52

Manual Confirm Enable ............................................................................................... 52

Extra CPR Interval Before 1st Analysis ....................................................................... 53

Duration of Extra CPR Interval .................................................................................... 53

Display Remaining CPR Timer .................................................................................... 53

TABLE OF CONTENTS

iv www.zoll.com 9650-0902-05 Rev. C

Wi-Fi Settings (Optional)...................................................................................................... 54

Full Disclosure Transfer Mode ..................................................................................... 54

Defib History Transfer Mode ........................................................................................ 54

Infrastructure Mode Options ........................................................................................ 54

DHCP/Static IP ............................................................................................................ 54

Local IP Address .......................................................................................................... 55

Gateway IP Address .................................................................................................... 56

Subnet Mask ................................................................................................................ 57

Use DNS ...................................................................................................................... 58

Primary/Secondary DNS IP Address ........................................................................... 58

SSID Names (up to 2 entries) ...................................................................................... 59

Server Name (Full Disclosure) ..................................................................................... 60

Server IP (Full Disclosure) ........................................................................................... 61

Server Port (Full Disclosure) ........................................................................................ 62

Server Name (Defib History) ........................................................................................ 63

Server IP (Defib History) .............................................................................................. 64

Server Port (Defib History) ........................................................................................... 66

Passphrase/Keys (up to 2 entries) ............................................................................... 67

Wi-Fi Transmission Mode Options....................................................................................... 68

Enable Report ID ......................................................................................................... 68

Wi-Fi Region ................................................................................................................ 68

Wi-Fi Radio .................................................................................................................. 68

9650-0902-05 Rev. C 1

Chapter 1

Introduction

The R Series

is designed with several user selectable features that allow operators to

configure the device according to their protocols and local requirements. This manual describes

the configuration settings (options and defaults) and how to change them for ALS, Plus, and

BLS models. References to AED settings are for Plus and BLS models only.

Note: Your unit may not contain all features listed. For BLS/Plus units, some features are

available in manual mode operation only.

For more information, see the following sections:

• “Entering System Configuration Mode” on page 2

• “Printing Configuration Settings and Activity Logs” on page 3

• “Uploading Data from a Compact Flash Card” on page 6

• “Saving Configuration to a Compact Flash Card” on page 8

• “Restoring Default Values” on page 9

• “Accessing and Changing Configuration Settings” on page 10

• “Leaving Configuration Mode” on page 11

Chapter 1 Introduction

2 9650-0902-05 Rev. C

Entering System Configuration Mode

In order to make any changes to unit configuration, you must first power on the unit in System

Configuration mode.

Procedure

Follow these steps to power on the unit in System Configuration mode:

Step Action

1. Turn the selector switch to OFF, and wait 10

seconds.

Simultaneously press and hold the right-most and

left-most softkeys (below the monitor) while turning

the selector switch to MONITOR (for ALS models)

or ON (for Plus and BLS models), and hold the

softkeys for approximately 4 seconds.

The unit powers on in System Configuration mode.

2. Enter the passcode using the appropriate softkeys.

Note: When you enter System Configuration for

the first time, enter the default pass code of

00000000.

To change a digit, use the Delete softkey to

highlight the entry and re-enter the digit.

When all 8 digits have been entered, the unit

automatically advances to the Select Language

screen.

3. Use the Prev Value and Next Value softkeys to

toggle the highlighted area between the language

options.

4. Press the Enter softkey to select the highlighted

language.

All subsequent configuration menus will be in the

selected language.

The unit automatically advances to the Main

Configuration menu.

System Configuration

Set Configuration Passcode

or Power Off to Exit

0 0 0 0 ? ? ? ?

Delete

System Configuration

Enter Configuration Passcode

or Power Off to Exi

0 0 0 ? ? ? ? ?

Delete

Enter

Exit

Config

Value

System Configuration

Select Language

ENGLISH

FRANCAIS

System Configuration

Change

Config

Exit

Config

Read

From

Card

Restore

Defaults

Printing Configuration Settings and Activity Logs

9650-0902-05 Rev. C 3

Printing Configuration Settings and Activity Logs

To print the current configuration or activity log of your unit while the unit is in the System

Configuration mode, press the Print softkey from the Main System Configuration menu. For

instructions on putting the unit in System Configuration mode, refer to the previous section,

“Entering System Configuration Mode.”

Printing Configuration Settings

In System Configuration mode, press the Print softkey, then the Print Config softkey to print a

stripchart of all the unit’s configuration settings. See a copy of a sample Configuration Report

below.

Note: In normal operation, you can print the configuration by pressing the following

softkeys: Options, More, then Print Config.

Chapter 1 Introduction

4 9650-0902-05 Rev. C

Printing Configuration Settings and Activity Logs

9650-0902-05 Rev. C 5

Printing the Activity Log

In System Configuration mode, press the Print softkey, then the Print Activity Log softkey to

print a stripchart of the unit’s activity log. The log consists of the last 1,024 user entries or

system prompts. See a copy of a sample Activity Log report below.

Chapter 1 Introduction

6 9650-0902-05 Rev. C

Uploading Data from a Compact Flash Card

You can upload data from a compact flash card to perform the following tasks:

• Copy the configuration of one unit to any number of units

• Install new software to the unit

• Copy a second language to the unit

Procedure

Follow these steps to load a configuration, another language, or software from a compact flash

card:

If you want to review configuration settings, press the Change Config softkey. See “Accessing

and Changing Configuration Settings” on page 10 for more information. If you want to leave

Step Action

1. Install the compact flash card in the R Series unit,

and power on the unit in System Configuration mode

as described in “Entering System Configuration

Mode” on page 2.

2. Press the Read From Card softkey to display the

Read Card screen.

Use the Prev Value and Next Value softkeys to

toggle the highlighted area between the following

options:

• LANGUAGE - allows you to upload a second

language to the unit. English is always on the

unit as default, and one other language can be

added.

• CONFIGURATION -allows you to read the

configuration data from a card, thereby

configuring this unit.

• PROGRAM - allows you to install new software

in either the PD processor or the ECG processor.

Note: Do not install an older version of software

over a newer version because it will cause

software problems.

3. Press the Enter softkey to initiate reading and

storing the information from the installed compact

flash card.

Once the card has been read and loaded, the unit

displays the CARD READ message (for a language

card) or the CARD READ and PRESS CHANGE

CONFIG TO VIEW messages (for a configuration

card).

System Configuration

Change

Config

Exit

Config

Read

From

Card

Restore

Defaults

Enter

Value

System Configuration

Read Which Type of Card?

LANGUAGE

CONFIGURATION

PROGRAM

System Configuration

Card Read

Press Change Config to View

Change

Config

Exit

Config

Read

From

Card

Restore

Defaults

Uploading Data from a Compact Flash Card

9650-0902-05 Rev. C 7

System Configuration mode, press the Exit Config softkey. See “Leaving Configuration

Mode” on page 11 for more information.

If the unit encounters an error reading the memory card, one of the following error messages is

displayed:

Error Message Description

CARD READ FAILED No response is detected from the card reader.

BAD CARD The unit cannot read the card.

NO CARD INSERTED The card is not installed in the data card slot.

Chapter 1 Introduction

8 9650-0902-05 Rev. C

Saving Configuration to a Compact Flash Card

Whenever you exit configuration mode, you can optionally save the configuration to a compact

flash card. This allows you to copy the configuration from one unit to any number of units.

Procedure

Follow these steps to save configuration data to a compact flash card:

Step Action

1. Power on the unit in System Configuration mode as

described in “Entering System Configuration Mode”

on page 2.

2. Press the Exit Config softkey to display the Exit

Configuration screen, and then install the flash card

in the R Series unit.

3. Press the Enter softkey to save the configuration

changes and exit.

The unit displays the SAVING CONFIGURATION

and DO NOT POWER OFF messages and then the

Save Changes To Card screen appears.

4. Press the Next Item softkey to highlight YES, then

press the Enter softkey.

The unit displays the SAVING TO CARD message

and then the POWER OFF TO EXIT

CONFIGURATION message.

System Configuration

Change

Config

Exit

Config

Read

From

Card

Restore

Defaults

Enter

Item

System Configuration

Save Changes and Exit

Discard Changes and Exit

Return to Main Menu

Enter

Item

System Configuration

Save Changes to Card?

YES

Restoring Default Values

9650-0902-05 Rev. C 9

Restoring Default Values

You can restore all configuration settings to their factory default settings. Only the display

language, if different from the default, does not change.

Procedure

Follow these steps to restore all configuration settings to default values:

If you want to review configuration settings, press the Change Config softkey. See “Accessing

and Changing Configuration Settings” on page 10 for more information. If you want to leave

System Configuration mode, press the Exit Config softkey. See “Leaving Configuration

Mode” on page 11 for more information.

Step Action

1. Power on the unit in System Configuration mode as

described in “Entering System Configuration Mode”

on page 2.

2. Press the Restore Defaults softkey to reconfigure

settings to their default settings.

Once default settings are restored, the unit displays

the DEFAULTS RESTORED and PRESS CHANGE

CONFIG TO VIEW messages.

System Configuration

Change

Config

Exit

Config

Read

From

Card

Restore

Defaults

System Configuration

Defaults Restored

Press Change Config to View

Change

Config

Exit

Config

Read

From

Card

Restore

Defaults

Chapter 1 Introduction

10 9650-0902-05 Rev. C

Accessing and Changing Configuration Settings

You can change the current value for any configuration setting. You access most of the settings

in the same way as described below. Additional steps are required to access and modify several

settings. For those settings, the additional steps are provided with the setting description in the

next chapter.

Procedure

Follow these steps to access the settings.

Step Action

1. Press the Change Config softkey from the Main

System Configuration screen.

The unit advances to the Select Configuration

Category screen.

2. Use the softkeys on the screen to move through

the list and select a category, or to exit as

follows:

•  — moves the highlight up, down,

left, and right through the list of categories.

• Enter — provides you access to the options

of the highlighted category. Press this softkey

once you have highlighted the appropriate

category.

• Main Menu — returns you to the Main

System Configuration screen.

3. Once you select and access the options for a

category, you can highlight the specific setting

you want to change, then press the Change

Value softkey until the appropriate value is

displayed.

Note: Some options require and evoke an

additional screen to set the value (for

example, setting the Device Identifier).

Specific instructions for those options

are provided in the next chapter.

Enter

System Configuration

Select Configuration Category

Set/Review

Main

General

ECG

Audio

Basic Defib

Advisory Defib

CPR

Pace

Alarms

Display

Printer & Report

Page 1 of 2

Enter

System Configuration

Select Configuration Category

Main

Readiness Test

AED Mode

NIBP

EtCO2

Wi-Fi

Page 2 of 2

Leaving Configuration Mode

9650-0902-05 Rev. C 11

Leaving Configuration Mode

Procedure

Follow the step below to leave System Configuration mode:

4. When you are finished, you can either press the

Category List softkey to return to the Category

screen, or press the Prev Item or Next Item

softkey to move to another option whose

settings you want to modify.

Step Action

1. Press the Exit Config softkey from the Main System

Configuration screen to display the Exit

Configuration screen.

Use the Prev Item and Next Item softkeys to toggle

the highlighted area between the following options:

• SAVE CHANGES AND EXIT - saves all

configuration changes you made and prompts

you to Save to Card. If you specify Yes, the

configuration information is saved to the installed

Compact Flash card. Lastly, the message

POWER OFF TO EXIT CONFIG is displayed.

Power off the unit.

• DISCARD CHANGES AND EXIT-disregards the

changes you made and displays the message

POWER OFF TO EXIT CONFIG. Power off the

unit.

• RETURN TO MAIN MENU- returns you to the

Main System Configuration screen, where you

can make more changes by selecting the

Change Config softkey. You do not have to re-

enter the passcode

Note:

No changes are made if you turn the unit

off without saving the configuration.

Enter

Item

System Configuration

Save Changes and Exit

Discard Changes and Exit

Return to Main Menu

Chapter 1 Introduction

12 9650-0902-05 Rev. C

9650-0902-05 Rev. C 13

Chapter 2

Configuration Settings

This chapter describes all of the configuration settings on the R Series and includes the

following sections.

• “General Settings” on page 14

• “ECG Settings” on page 19

• “Basic Defibrillation Settings” on page 22

• “Advisory Defib” on page 24

• “CPR Settings” on page 31

• “Pace Settings” on page 34

• “Alarms Settings” on page 35

• “Display Settings” on page 41

• “NIBP Settings (Optional)” on page 44

• “EtCO2 Settings (Optional)” on page 47

• “Printer & Report Settings” on page 49

• “Readiness Test Settings” on page 50

• “AED Mode” on page 52

• “Wi-Fi Settings (Optional)” on page 54

Note: The instructions in this chapter assume that you powered on the unit in System

Configuration mode as described in “Entering System Configuration Mode” on

page 2, and are familiar with how to access the settings, see “Accessing and Changing

Configuration Settings” on page 10.

Chapter 2 Configuration Settings

14 9650-0902-05 Rev. C

General Settings

General settings are attributes that affect the unit’s basic operation and accessibility and

include:

• Device Identifier

• Configuration Mode Passcode

• Code Markers

Device Identifier

The Device Identifier feature allows you to set an 11-digit device identifier code. This code is

divided into two sub codes: the site ID (consisting of eight alphanumeric characters) and the

device ID (consisting of three alphanumeric characters). The device identifier is printed on the

summary report and fax printouts.

Values are as follows:

Procedure

Follow these steps to set up a device identifier.

Possible Values: 0 through 9, A through Z, blank and underscore inclusive for each digit.

Default: 00000000 000

Step Action

1. From the Select Configuration Categories screen,

select General, then press the Enter softkey.

The General Settings screen appears.

2. Select DEVICE IDENTIFIER and press the

Change Value softkey.

The Device Identifier screen appears.

Item

System Configuration

General Settings

Set/Review

CONFIGURATION

MODE PASSCODE

CODE MARKERS

00000000

Config/Review

Main

Exit

Config

Category

List

Change

Value

DEVICE IDENTIFIER

ABCDEFGH 777

Page 1 of 1

System Configuration

Set Site ID

0 0 0 0 0 0 0 0

Set Device ID

0 0 0

Cancel

Del

Return

Enter

Char

General Settings

9650-0902-05 Rev. C 15

3. In the character selection table:

•

 lets you move to the next or previous

characters.

Use the softkeys as follows:

•

 — moves the highlight up, down,

left, and right through the character selection

table.

• Enter Char — enters the highlighted

character for 8 digits of the Site ID and the 3

digits of the Device ID.

• Return — returns you to the General Settings

screen. Press the Return softkey when you

are finished entering the IDs. Note that

selecting Enter also returns you to the

General Settings screen.

Step Action

Chapter 2 Configuration Settings

16 9650-0902-05 Rev. C

Configuration Mode Passcode

This feature allows you to set an 8-digit system configuration passcode. Once set, only those

people who know the passcode can access the configuration mode and modify settings.

Values are as follows:

Procedure

Follow these steps to set up a configuration mode passcode:

Possible Values: 0 through 3 inclusive for each digit

Default: 00000000

Step Action

1. From the Select Configuration Categories

screen, select General, then press the Enter

softkey.

The General Settings screen appears.

2. Select CONFIGURATION MODE PASSCODE

and press the Change Value softkey.

The Set Configuration Passcode screen appears.

3. Use the softkeys as follows:

• Prev Digit — moves the highlight left to the

previous digit.

• Inc Digit or Dec Digit — increments or

decrements the value of the selected digit.

• Next Digit — moves the highlight right to the

next digit to be entered.

• Enter — saves the values that you entered

and returns the unit to the General

Configuration menu.

Item

System Configuration

General Settings

Set/Review

CODE MARKERS Config/Review

Main

Exit

Config

Category

List

Change

Value

DEVICE IDENTIFIER

ABCDEFGH 777

Page 1 of 1

00000000

CONFIGURATION

MODE PASSCODE

Digit

Enter

Dec

Digit

Inc

Digit

System Configuration

Set Configuration Passcode

0 0 0 0 0 0 0 0

General Settings

9650-0902-05 Rev. C 17

Code Markers

This setting allows you to review and change the preconfigured list of Code Markers for use in

DEFIB, MONITOR, and PACE modes. Code Marker settings are language dependent. You can

specify up to three groups (MONITOR, DEFIB, and PACE) of 20 entries each.

Procedure

Follow these steps to review, change, or reset code marker settings:

Step Action

1. From the Select Configuration Categories

screen, select General, then press the Enter

softkey.

The General Settings screen appears.

2. Select CODE MARKERS and press the Change

Value softkey.

The Select Code markers screen appears.

3. Select either DEFIB CODE MARKERS,

MONITOR CODE MARKERS, or PACE CODE

MARKERS, then press the Change Value

softkey to toggle between Change/Review or Set

to Defaults.

• If you select Set to Defaults, press the Enter

softkey to set the chosen code markers to

their default values.

• If you select Change/Review, press the Enter

softkey to access the screen that allows you

to change the marker, as shown.

Note: This example shows the screen that

allows you to change DEFIB CODE

MARKERS.

Only 8 items are displayed on the

screen at one time. When you get to the

last item on the screen and press the

Next Item softkey, you see the next 8

items. When you get to the last item on

that screen and press the Next Item

softkey, you see the remaining 4 items.

Item

System Configuration

General Settings

Set/Review

Main

Exit

Config

Category

List

Change

Value

DEVICE IDENTIFIER

ABCDEFGH 777

Page 1 of 1

00000000

CONFIGURATION

MODE PASSCODE

CODE MARKERS

Config/Review

Item

System Configuration

General Settings

Set/Review

Enter

Return

Change

Value

PACE

CODE MARKERS

Config/Review

Page 1 of 1

Config/Review

MONITOR

CODE MARKERS

DEFIB

CODE MARKERS

Config/Review

Return

Item

System Configuration

Item 2: Intubate

Item 3: EPI

CPR

Item 1: CPR

Defib Markers Markers List

Item 4: LIDO

Item 5: Narcan

Item 6: B-block

Item 7: Atrovent

Item 8: Mag Sulf

EPI

Atrop

DOPA

PHEN

Bicarb

Aspirin

Oxygen

Change

Value

Delete

to End

Chapter 2 Configuration Settings

18 9650-0902-05 Rev. C

4. Use the softkeys as described to modify code

marker items as needed:

• Prev Item and Next Item — scrolls the

highlight to the next or previous code marker

item.

• Change Value — allows you to pick a new

marker for the selected item number. When

you press the Change Value softkey, three

new softkeys become available that allow

you to highlight and select the code marker

treatment for this item. They are:

— Prev Marker and Next Marker — allow

you to scroll through the Markers List and

highlight the appropriate treatment.

— Enter Marker — set the highlighted

treatment for this code marker item.

• Delete to End — delete all configured

markers from the highlighted item number to

the end of the list. You can then enter new

clinical actions for each item.

• Return — returns you to the previous menu.

Step Action

ECG Settings

9650-0902-05 Rev. C 19

ECG Settings

ECG monitoring settings are attributes associated with using the R Series unit for ECG

monitoring, and include:

• Notch Filter

• Display Lead on Power-Up

• Frequency Response

• Gain on Power Up

• Enable Leads Off

• Enable Pacer Detection

Notch Filter

This setting allows you to select the ECG Notch Filter frequency for proper ac mains

interference rejection.

Values are as follows:

Display Lead on Power-Up

This setting allows you to select the lead to be displayed when you power on the unit.

Values are as follows:

Frequency Response

This setting allows you to select the ECG filter bandwidth to be used during ECG monitoring.

You can set the unit’s frequency to either help reduce noise, help with the diagnostic response,

or set it as a default response.

Values are as follows:

Possible Values: 50 Hz, 60 Hz

Default: 60 Hz

Possible Values: Paddles/Pads, Lead I, Lead II, Lead III

Default: Paddles/Pads

Possible Values: 0.5 - 21 Hz, 0.5 - 40 Hz, 1.0 - 21 Hz

Default: 0.5 - 21 Hz

Chapter 2 Configuration Settings

20 9650-0902-05 Rev. C

Gain on Power Up

This setting allows you to select the default size of the displayed ECG signal when you power

on the unit.

Values are as follows:

Enable Leads Off

This setting specifies whether the unit displays the ECG LEADS OFF message and a flat

dashed ECG waveform when the unit detects that ECG leads do not have proper contact with

the patient or the cable is not properly attached to the R Series unit. When set to No, the unit

displays the POOR LEAD CONTACT message and the detected ECG signals when the cable or

ECG leads are not properly attached to the patient or unit. When set to Yes, the unit displays the

ECG LEADS OFF message and a flat dashed ECG waveform when the cable or ECG leads are

not properly connected.

Caution Use care when interpreting ECG waveforms when the POOR LEAD CONTACT message

displays; the ECG waveform may include a significant amount of artifact. Whenever possible,

re-attach the leads before interpreting the waveform.

Values are as follows:

Note: When in Pacer mode, the R Series unit functions as if this configuration is set to Yes.

Enable Pacer Detection

This setting allows you to specify whether the unit should detect pacemaker signals from a

patient with an implantable pacemaker and indicate those signals on the display. When you set

this setting to Yes, a pacemaker marker is displayed on the ECG trace whenever the unit detects

implanted pacer stimuli.

You can override this setting during normal operations. This setting simply indicates the default

setting when you power on the unit.

Values are as follows:

Possible Values: 0.5 cm/mV, 1.0 cm/mV, 1.5 cm/mV, and 2.0 cm/mV

Default: 1.0 cm/mV for Manual mode

Possible Values: Yes, No

Default: Yes

Possible Values: Yes, No

Default: Yes

Audio Settings

9650-0902-05 Rev. C 21

Audio Settings

The Tone settings control audio functions on the R Series unit, and include:

• QRS Volume on Power-Up

• Low Battery Tone

• Enable Corrective Voice Prompts

QRS Volume on Power-Up

This setting allows you to select the default QRS beeper volume when you power on the unit. If

you set this setting to Off, the unit does not beep during ECG monitoring.

Values are as follows:

Low Battery Tone

This setting allows you to select the interval between Low Battery warning beeps. The Low

Battery warning message is displayed once per minute, regardless of this setting.

Values are as follows:

Enable Corrective Voice Prompts

This setting allows you to specify whether voice prompts accompany the following corrective

messages:

• Press Charge

• Select Defib Mode

• Remove Sync

• Release Shock

• Use Paddle Discharge

Values are as follows:

Possible Values: On, Off

Default: On

Possible Values: 1 Min, 5 Min

Default: 5 Min

Possible Values: Yes, No

Default: Yes

Chapter 2 Configuration Settings

22 9650-0902-05 Rev. C

Basic Defibrillation Settings

The Basic Defibrillation settings control functions related to performing defibrillation with the

R Series unit in Manual mode and include:

• Defib Default to Pads

• Basic Auto Energy Escalation

• Retain Sync After Defib

• Defib Ready Hold Time

• Enable Remote Sync

Defib Default to Pads

This setting allows you to override the “Display Lead on Power-Up” setting and use Pads/

Paddles whenever the unit is switched to DEFIB mode.

Values are as follows:

Basic Auto Energy Escalation

This setting allows you to configure the unit to automatically increment defibrillation energy to

pre-specified levels after each of the first two shocks in Manual mode (see “Energy Level:

Shock 1” on page 24, “Energy Level: Shock 2” on page 25, and “Energy Level: Shock 3” on

page 25). When set to Yes, the ENERGY INCREMENTED message is displayed whenever the

unit automatically increments the selected defibrillator energy after delivery of a shock with

paddles or MFE pads.

Note: Manually changing the energy level outside the pre-programmed sequence and

delivering a shock disables the auto energy escalation function until the unit is turned

off for more than 10 seconds, then turned back on.

This option increments the energy level regardless of Shock Advisory activation or status.

Values are as follows:

Retain Sync After Defib

This setting allows you to configure the unit to remain in SYNC mode after a synchronized

cardioversion shock. SYNC mode remains on until the Sync On/Off softkey is pressed again or

the unit is switched out of DEFIB mode.

Values are as follows:

Possible Values: Yes, No

Default: Yes

Possible Values: Yes, No

Default: Yes

Possible Values: Yes, No

Default: No

Basic Defibrillation Settings

9650-0902-05 Rev. C 23

Defib Ready Hold Time

This setting allows you to specify the amount of time that the R Series unit will hold a charge

before disarming.

Values are as follows:

Enable Remote Sync

This setting allows you to enable and disable the Remote Sync feature. If disabled (No), you

can perform synchronized cardioversion using only the R Series ECG signal. If enabled (Yes),

you can press the Sync On/Off softkey to select either Remote Sync or Sync.

Values are as follows:

Possible Values: 60 secs, 120 secs

Default: 60 secs

Possible Values: Yes, No

Default: No

Chapter 2 Configuration Settings

24 9650-0902-05 Rev. C

Advisory Defib

The Advisory Defibrillation settings control functions related to performing defibrillation with

an R Series unit in Advisory mode and include:

• Energy Level: Shock 1

• Energy Level: Shock 2

• Energy Level: Shock 3

• Ped Energy Level Shock 1

• Ped Energy Level Shock 2

• Ped Energy Level Shock 3

• Auto Analyze

• Enable Check Pulse Prompt

• Check Patient Prompt

• Auto Charge in Advisory Mode

• Enable Voice in Advisory Mode

• Display DO CPR Message

• CPR Message After No Shock Advised

• CPR Message After Shock

• Stacked Shocks

• Restart Analysis After CPR

• CPR Interval

Energy Level: Shock 1

This setting allows you to select the energy level used for the first shock delivered by the

defibrillator when the unit is:

• in AED mode or Advisory mode and using pads

• in Manual mode, using external paddles or pads

Energy Level: Shock 1 is the energy level to which the unit defaults when you power on the

unit with external paddles or pads connected.

Values are as follows:

Possible Values: Adult: 1-10, 15, 20, 30, 50, 75, 100, 120, 150, and 200 J

Default: Adult: 120 J

Advisory Defib

9650-0902-05 Rev. C 25

Energy Level: Shock 2

This setting allows you to select the energy level used for the second shock delivered by the

defibrillator when the unit is:

• in AED mode or Advisory mode and using pads

• in Manual mode, using external paddles or pads, and Basic Auto Energy Escalation is set to

Yes

Values are as follows:

Energy Level: Shock 3

This setting allows you to select the energy level used for the third and all subsequent shocks

delivered by the defibrillator when the unit is:

• in AED mode or Advisory mode and using pads

• in Manual mode, using external paddles or pads, and Basic Auto Energy Escalation is set to

Yes

Values are as follows:

Ped Energy Level Shock 1

This setting allows you to select the energy level used for the first pediatric shock delivered by

the defibrillator when the unit is:

• in Advisory mode and using OneStep™ Pediatric electrodes.

• in Manual mode, using OneStep Pediatric electrodes

Ped Energy Level: Shock 1 is the energy level to which the unit defaults when you power on the

unit with pediatric electrode pads.

Values are as follows:

Warning! The R Series will default to pediatric Shock 1, 2, and 3 energies only when ZOLL

OneStep pediatric electrodes are used. With

pedi-padz

and pedi-padz II (or other non-

ZOLL pediatric electrodes), you are required to manually set the selected energy to

pediatric levels, per institutional protocols.

Possible Values: Adult: 1-10, 15, 20, 30, 50, 75, 100, 120, 150, and 200 J

Default: Adult: 150 J

Possible Values: Adult: 1-10, 15, 20, 30, 50, 75, 100, 120, 150, and 200 J

Default: Adult: 200 J

Possible Values: Pediatric: 1-10, 15, 20, 30, 50, 70, 85, 100, 120, 150, and 200 J

Default: Pediatric: 50 J

Chapter 2 Configuration Settings

26 9650-0902-05 Rev. C

Ped Energy Level Shock 2

This setting allows you to select the energy level used for the second pediatric shock delivered

by the defibrillator when the unit is:

• in Advisory mode and using OneStep Pediatric electrodes.

• in Manual mode, using OneStep Pediatric electrodes and Basic Auto Energy Escalation is

set to Yes

Values are as follows:

Ped Energy Level Shock 3

This setting allows you to select the energy level used for the third and all subsequent shocks

delivered by the defibrillator when the unit is:

• in Advisory mode and using OneStep Pediatric electrodes.

• in Manual mode, using OneStep Pediatric electrodes and Basic Auto Energy Escalation is

set to Yes.

Values are as follows:

Auto Analyze

This setting allows you to specify whether the unit automatically repeats ECG rhythm analyses

after the delivery of shocks in Advisory mode and works in conjunction with the Stacked

Shocks setting described on page 30. Enabling this setting also enables the occurrence of post-

shock prompting to DO CPR and PRESS ANALYZE. When set to No, which is the Manual

mode default, the unit does not perform analysis automatically (with the exception of Smart

Alarms and the first analysis when you power on the unit in AED mode, if the unit is

configured to analyze when you power on the unit).

When set to Yes and the Stacked Shocks options is set to 3, the unit automatically reanalyzes

the patient’s ECG rhythm after the first and second shocks in each three-shock sequence.

Following delivery of the final shock, the unit stops automatic reanalysis and either displays a

CHECK PULSE prompt, or immediately begins a CPR interval, depending on additional

settings. This function operates only when the Auto Charge in Advisory Mode is set to Yes.

Values are as follows:

Possible Values: Pediatric: 1-10, 15, 20, 30, 50, 70, 85, 100, 120, 150, and 200 J

Default: Pediatric: 70 J

Possible Values: Pediatric: 1-10, 15, 20, 30, 50, 70, 85, 100, 120, 150, and 200 J

Default: Pediatric: 85 J

Possible Values: Yes, No

Default: Yes

Advisory Defib

9650-0902-05 Rev. C 27

Enable Check Pulse Prompt

This setting works in conjunction with the Auto Analyze function and determines whether the

unit displays the prompt CHECK PULSE for 10 seconds immediately after delivery of the final

shock in a stacked shock sequence, after each No Shock Advised analysis result, or both. After

CHECK PULSE clears, the CPR interval begins.

When set to No, the unit immediately begins the CPR interval following delivery of the final

shock or after each No Shock Advised analysis result.

Values are as follows:

Check Patient Prompt

This setting allows you to change the display message and the voice prompt issued when a

shockable rhythm has been detected by background ECG analysis and Heart Rate Alarms are

enabled.

Values are as follows:

Auto Charge in Advisory Mode

This setting allows you to specify whether the unit automatically charges the defibrillator to the

configured or user-selected energy setting after detection of a shockable rhythm by ECG

analysis. When set to Yes, the unit automatically charges the defibrillator to the configured or

user-selected energy setting. When set to No, it does not.

Values are as follows:

Possible Values: Yes, No, After No Shock Only, After Shock Only

Default: No

Possible Values: CHECK PATIENT, PRESS ANALYZE

Default: CHECK PATIENT

Possible Values: Yes, No

Default: Yes

Chapter 2 Configuration Settings

28 9650-0902-05 Rev. C

Enable Voice in Advisory Mode

This setting allows you to enable or disable voice prompts when using shock advisory functions

(ECG analysis) in Manual mode. If enabled, the voice prompts sound at the appropriate time. If

disabled, the unit emits two beeps instead of the voice prompts in Manual mode.

Voice prompts are in the language specified by the Language option.

Values are as follows:

Display DO CPR Message

This setting allows you to specify whether the unit displays the configured CPR prompt

(described in CPR Text Message) for the configured CPR time interval after each set of stacked

shocks, even if a perfusing rhythm is present. The unit behaves differently depending on this

particular setting value.

Note: This setting is always set to Yes in AED mode.

• When set to No (the Manual mode default), the unit behaves as follows:

— At the end of any analysis with an outcome of no shock advised, the unit displays the NO

SHOCK ADVISED message. The unit then remains idle for the configured CPR interval

duration. After the CPR interval, if the ANALYZE softkey has not been pressed, the

PRESS ANALYZE message is displayed and remains until a new analysis is started or the

mode is changed.

— At the end of a stacked shock sequence (assuming the final shock is delivered) and when

the optional 10 second CHECK PULSE message disappears, the CPR interval begins.

The unit remains idle for the duration of the CPR interval. After the CPR interval, if the

ANALYZE softkey has not been pressed, the PRESS ANALYZE prompt is displayed and

remains until a new analysis is started or the mode is changed.

— If the defibrillator disarms itself after it was charged (because the Defib Ready time

elapsed before a shock was delivered), the unit displays the PRESS ANALYZE prompt

until the ANALYZE softkey is pressed.

• When set to Yes, the unit behaves as follows:

— At the end of any analysis with an outcome of no shock advised, the unit displays the NO

SHOCK ADVISED message for 10 seconds, after which the message is cleared and the

configured CPR prompt is displayed for the duration of the CPR interval. After the CPR

interval, the PRESS ANALYZE prompt is displayed until a new analysis is started or a

mode change occurs. You can start a new analysis during the CPR interval by pressing

the ANALYZE softkey.

— At the end of a stacked shock sequence (assuming the final shock is delivered) and when

the optional 10 second CHECK PULSE message disappears, the CPR interval begins.

The configured CPR prompt is displayed for the duration of the CPR interval. After the

CPR interval, the CPR prompt is cleared and a new analysis starts automatically.

Possible Values: Yes/No

Default: Yes

Advisory Defib

9650-0902-05 Rev. C 29

— If the defibrillator disarms itself after it was charged (because the Defib Ready time

elapsed before a shock was delivered), the unit displays the PRESS ANALYZE prompt

until the ANALYZE softkey is pressed.

Note: The Display DO CPR Message feature is operational only when the Auto Charge in

Advisory Mode and Auto Analyze options are both set to Yes.

Values are as follows:

CPR Message After No Shock Advised

This parameter determines which CPR message/voice prompt is issued during the CPR interval

after a No Shock Advised analysis result. The selected message is displayed throughout the

entire CPR interval.

Values are as follows:

CPR Message After Shock

This parameter determines which CPR message/voice prompt is issued during the CPR interval

after the delivery of the final shock in a stacked shock sequence. The selected message is

displayed throughout the entire CPR interval.

Values are as follows:

Possible Values: Yes, No

Default: Yes

Possible Values: “If No Pulse, Perform CPR”, “Perform CPR”

Default: Perform CPR

Possible Values: “If No Pulse, Perform CPR”, “Perform CPR”

Default: “Perform CPR”

Chapter 2 Configuration Settings

30 9650-0902-05 Rev. C

Stacked Shocks

The setting specifies the number of stacked shocks that must be administered prior to the

activation of a CPR interval and works in conjunction with the Auto Analyze setting. If set to 3,

the unit will auto analyze 3 times before prompting the user. If set to 1, the unit will auto

analyze once.

Values are as follows:

Restart Analysis After CPR

When this parameter is set to Yes, the analysis starts automatically after the CPR interval

following each stacked shock sequence. Analyses do not automatically restart after a CPR

interval following No Shock Advised results. When this parameter is set to No, the PRESS

ANALYZE message is displayed, but the analysis does not restart.

Note: This setting is always set to Yes in mode.

Values are as follows:

CPR Interval

This setting allows you to specify the duration of the CPR interval as described in the Display

DO CPR Message setting. Values are as follows:

Possible Values: 1, 3

Default: 1

Possible Values: Yes, No

Default: No

Possible Values: 1, 1.5, 2, 2.5, 3, 3.5, or 4 minutes

Default: 2 minutes

CPR Settings

9650-0902-05 Rev. C 31

CPR Settings

The CPR settings control functions related to Real CPR Help

function:

• Enable CPR Voice Prompts

• Enable CPR Display

• Enable CPR Dashboard

• Display Release Bar

• Enable CPR Metronome

• Target CPR Depth

• CPR Depth Units

• Display Fully Release Prompt

• Display Filtered ECG on Trace1

Enable CPR Voice Prompts

This setting allows you to enable (Yes) or disable (No) voice prompts during CPR. Voice

prompts are in the language specified by the Language option.

Note: This setting is always set to Yes in AED mode.

Values are as follows:

Enable CPR Display

This setting allows you to enable (Yes) or disable (No) the display of the CPR indicator on the

monitor.

Values are as follows:

Enable CPR Dashboard

If Enable CPR Display is set to Yes, this setting allows you to enable (Yes) or disable (No) the

display of the CPR Dashboard™ at the top of the screen. The CPR Dashboard consists of the

CPR Rate and Depth numeric values, the optional Compression Release Bar, and the

CPR Index™.

Possible Values: Yes, No

Default: Yes

Possible Values: Yes, No

Default: Yes

Possible Values: Yes, No

Default: No

Chapter 2 Configuration Settings

32 9650-0902-05 Rev. C

Display Release Bar

If Enable CPR Dashboard is set to Yes, this setting allows you to enable (Yes) or disable (No)

the display of the Compression Release Bar in the CPR Dashboard.

Enable CPR Metronome

This setting allows you to enable (Yes) or disable (No) the audible CPR metronome.

Note: This setting is always set to Yes in AED mode.

Values are as follows:

Target CPR Depth

This parameter allows you to select the minimum compression depth required for Good

Compressions: 1.5 inches (3.8 cm) or 2.0 inches (5.0 cm). If this parameter is set to 1.5 inches,

the reference markers on the CPR bar graph are displayed at 1.5 and 2.0 inches. If this

parameter is set to 2.0 inches, the reference markers on the CPR bar graph are displayed at 2.0

and 2.4 inches.

Values are as follows:

CPR Depth Units

This setting allows you to display the numeric depth value in inches (in) or centimeters (cm).

Values are as follows:

Display Fully Release Prompt

This parameter, when set to Yes, specifies that the FULLY RELEASE prompt will be displayed

every 45 seconds during CPR. If this parameter is set to No, the prompt is not displayed.

Possible Values: Yes, No

Default: No

Possible Values: Yes, No

Default: Yes

Possible Values: 1.5 inches, 2.0 inches

Default: 1.5 inches

Possible Values: in, cm

Default: in

CPR Settings

9650-0902-05 Rev. C 33

Values are as follows:

Display Filtered ECG on Trace1

If Display CPR Dashboard is set to Yes, this setting allows you to display the See-Thru CPR

filtered waveform on the top trace.

Possible Values: Yes, No

Default: No

Possible Values: Yes, No

Default: No

Chapter 2 Configuration Settings

34 9650-0902-05 Rev. C

Pace Settings

The Pace settings are attributes that control functions related to performing pacing with an

R Series unit and include:

• Pace Rate Setting on Power-Up

• Async Softkey in Pace Mode

Pace Rate Setting on Power-Up

This setting allows you to set the default pace rate, pulses per minute (ppm), of the R Series

when you power on the unit.

Values are as follows:

Async Softkey in Pace Mode

This setting allows you to set the unit to display the Async Pacing On/Off softkey when the

unit is in Pace mode. For information about Asynchronous Pacing, refer to the R Series

Operator’s Guide.

Values are as follows:

Possible Values: 30 ppm to 102 ppm (inclusive in increments of 4 ppm)

Default: 70 ppm

Possible Values: Yes, No

Default: Yes

Alarms Settings

9650-0902-05 Rev. C 35

Alarms Settings

Alarm settings are attributes associated with Alarm states and thresholds for the R Series unit

and include:

• Alarm Limits at Power Up

• Alarms Active at Power Up

Chapter 2 Configuration Settings

36 9650-0902-05 Rev. C

Alarm Limits at Power Up

This option allows you to enable or disable, and set high and low threshold values for the ECG

Heart Rate, and the SpO

alarms on the R Series unit. All alarms listed below (Heart Rate and

optional devices SpO

, EtCO

, NIBP) are enabled by default. Values are as follows:

Possible Values: Heart Rate:

High: 60 - 280 beats per minute (BPM) inclusive in 5 BPM increments

Low: 20 - 100 beats per minute (BPM) inclusive in 5 BPM increments

Optional Devices:

SpO

High: 72-100% in 1% increments

Low: 70-98% in 1% increments

EtCO

High: 5-100 mmHg in increments of 5

0.6-13.3 kPa in increments of .67

0.6-13.1% in increments of .66

Low: 0-95 mmHg in increments of 5

0.0-12.6 kPa in increments of .67

0-12.5% in increments of 0.66

Resp Rate:

High: 5-150 breaths per minute in increments of 5

Low: 0-100 breaths per minute in increments of 5

NIBP Sys:

Adult:

High: 80-260 mmHg in increments of 5

10.7-34.7 kPa in increments of 0.67

Low: 40-140 mmHg in increments of 5

5.3-18.7 kPa in increments of 0.67

Pediatric:

High: 80-160 mmHg in increments of 5

10.7-21.3 kPa in increments of 0.67

Low: 35-140 mmHg in increments of 5

4.7-18.7 kPa in increments of 0.67

Neonatal:

High: 60-130 mmHg in increments of 5

8.0-17.3 kPa in increments of 0.67

Low: 25-120 mmHg in increments of 5

3.3-16.0 kPa in increments of 0.67

Alarms Settings

9650-0902-05 Rev. C 37

Possible Values: NIBP Dia:

Adult:

High: 50-200 mmHg in increments of 5

6.7-26.7 kPa in increments of 0.67

Low: 25-100 mmHg in increments of 5

3.3-13.3 kPa in increments of 0.67

Pediatric:

High: 50-130 mmHg in increments of 5

6.7-17.3 kPa in increments of 0.67

Low: 20-100 mmHg in increments of 5

2.7-13.3 kPa in increments of 0.67

Neonatal:

High: 30-105 mmHg in increments of 5

4.0-14.0 kPa in increments of 0.67

Low: 20-100 mmHg in increments of 5

2.7-13.3 kPa in increments of 0.67

NIBP Mean:

Adult:

High: 60-220 mmHg in increments of 5

8.0-29.3 kPa in increments of 0.67

Low: 30-120 mmHg in increments of 5

4.0-16.0 kPa in increments of 0.67

Pediatric:

High: 60-140 mmHg in increments of 5

8.0-18.7 kPa in increments of 0.67

Low: 30-120 mmHg in increments of 5

4.0-16.0 kPa in increments of 0.67

Neonatal:

High: 35-110 mmHg in increments of 5

4.7-14.7 kPa in increments of 0.67

Low: 30-105 mmHg in increments of 5

4.0-14.0 kPa in increments of 0.67

Chapter 2 Configuration Settings

38 9650-0902-05 Rev. C

Default: Heart Rate:

High: 150 BPM

Low: 30 BPM

Optional Devices:

SpO

High: 100%

Low: 85%

EtCO

High: 55 mmHg

7.3 kPa

7.2%

Low: 25 mmHg

3.3 kPa

3.2%

Resp Rate:

High: 120

Low: 5

NIBP Sys:

Adult:

High: 160 mmHg

21.3 kPa

Low: 90 mmHg

12.0 kPa

Pediatric:

High: 145 mmHg

19.3 kPa

Low: 75 mmHg

10.0 kPa

Neonatal:

High: 100 mmHg

13.3 kPa

Low: 50 mmHg

6.7 kPa

Alarms Settings

9650-0902-05 Rev. C 39

Default NIBP Dia:

Adult:

High: 110 mmHg

14.7 kPa

Low: 50 mmHg

6.7 kPa

Pediatric:

High: 100 mmHg

13.3 kPa

Low: 35 mmHg

4.7 kPa

Neonatal:

High: 70 mmHg

9.3 kPa

Low: 30 mmHg

4.0 kPa

NIBP Mean:

Adult:

High: 130 mmHg

17.3 kPa

Low: 60 mmHg

8.0 kPa

Pediatric:

High: 110 mmHg

14.7 kPa

Low: 50 mmHg

6.7 kPa

Neonatal:

High: 80 mmHg

10.7 kPa

Low: 35 mmHg

4.7 kPa

Chapter 2 Configuration Settings

40 9650-0902-05 Rev. C

Procedure

Follow these steps to change the state or value of the ECG Heart Rate alarms:

Alarms Active at Power Up

This setting allows you to specify whether alarms are automatically active when you power on

the unit. This setting applies to all alarms enabled by the Alarm Limits At Power Up setting.

Step Action

1. From the Select Configuration Categories screen,

select Alarms, then press the Enter softkey.

The Alarms Setting screen appears.

2. Select Alarm Limits at Power Up, and press the

Change Value softkey.

The Set Alarm Defaults screen appears.

3. Modify alarms using the softkeys as follows:

• Next Param and Prev Param — moves the

highlight through the various physiological

settings.

• Next Field — moves highlight to the next field

to the right. Use this key to change the High and

Low settings.

• Change Value — allows you to change the

value of the highlighted field. When you press

this softkey, the following softkeys become

available:

— Inc > and Dec < — increases and decreases

the value of the field.

— Enter — applies the value you specified for

this field.

— Cancel — returns you to the previous screen

without applying any changes.

• Return — enters the values you specified, and

returns you to the previous screen.

Item

System Configuration

Alarm Settings

Set/Review

Main

Exit

Config

Category

List

Change

Value

Page 1 of 1

ALARMS ACTIVE

AT POWER UP

ALARM LIMITS

AT POWER UP

Set/Review

Change

Value

Return

System Configuration

Set Alarm Defaults

Parameter State Low High

150

ECG HR

ENABLE

Param

Field

100

ENABLE

SpO2

ENABLEEtCO2

120

ENABLE

RESP RATE

160

ENABLE

NIBP SYS

110

ENABLENIBP DIA

130

ENABLENIBP MEAN

145

ENABLENIBP p SYS

Page 1 of 2

Display Settings

9650-0902-05 Rev. C 41

Values are as follows:

Display Settings

The Display settings are attributes that control what and how things appear on the R Series

monitor and include:

• Display Time

• Select Trace 2 At Power Up

• Select Trace 3 At Power Up

• ECG Color

• SpO2 Color

• CPR Color

• EtCO2 Color

• NIBP Color

• SPO2 at Power Up

Display Time

This setting specifies whether to display the elapsed time since the unit was turned on (Elapsed

Time), or the real time (Real Time), or not to display the time (Off).

The elapsed time continues to be counted for up to 10 seconds after you power off the unit. This

gives the operator adequate time to change the battery without resetting the elapsed timer.

Elapsed time is reset to zero (00:00) whenever the unit has been off for more than 10 seconds.

Values are as follows:

Select Trace 2 At Power Up

This setting allows you to set which waveform will appear in the Trace 2 position on the display

when you turn on the R Series unit.

Values are as follows:

Note: When you set this setting to 3 Lead ECG, the Select Trace 3 At Power Up setting

automatically defaults to 3 Lead ECG.

Possible Values: Yes, No

Default: No

Possible Values: Real Time, Off, Elapsed Time

Default: Off

Possible Values: Off, 3 Lead ECG, CPR, Filtered ECG, SpO2, EtCO2

Default: Filtered ECG

Chapter 2 Configuration Settings

42 9650-0902-05 Rev. C

Select Trace 3 At Power Up

This setting allows you to select which waveform will appear in the Trace 3 position on the

display when you turn on the R Series unit.

Values are as follows:

Note: When you select 3 Lead ECG, the Select Trace 2 At Power Up setting automatically

defaults to 3 Lead ECG.

ECG Color

This setting allows you to set the display color for the ECG waveform and information

displayed on the R Series monitor.

Values are as follows:

SpO

Color

This setting allows you to specify the color of the SpO

information displayed (if installed) on

the R Series monitor.

Values are as follows:

CPR Color

This setting allows you to specify the color of the CPR indicator and waveform on the R Series

monitor.

Values are as follows:

Possible Values: Off, 3 Lead ECG, CPR, Filtered ECG, SpO2, EtCO2

Default: Off

Possible Values: Red, Cyan, Purple, Blue, Green, Yellow, White

Default: Green

Possible Values: Cyan, Red, Purple, Yellow, White, Blue, Green

Default: Cyan

Possible Values: Red, Cyan, Purple, Blue, Green, Yellow, White

Default: Purple

Display Settings

9650-0902-05 Rev. C 43

EtCO

Color

This setting allows you to specify the color of the CO

indicator and waveform (if installed) on

the R Series monitor. Values are as follows:

NIBP Color

This setting allows you to specify the color of the NIBP indicator (if installed) on the R Series

monitor. Values are as follows:

SPO

at Power Up

This setting allows you to control whether the SPO

box appears on the R Series monitor (if

installed). If set to Yes, the box will be displayed regardless of whether the SPO

sensor is

connected to the unit. If set to No, the box will not appear until the sensor is connected to the

unit. Values are as follows:

Possible Values: Blue, Green, Cyan, Red, Purple, Yellow, White

Default: Yellow

Possible Values: White, Blue, Green, Cyan, Red, Purple, Yellow

Default: White

Possible Values: Yes, No

Default: No

Chapter 2 Configuration Settings

44 9650-0902-05 Rev. C

NIBP Settings (Optional)

NIBP configuration parameters are available for update only if the NIBP monitoring option is

installed on the unit, and include:

• Blood Pressure Units

• Trigger NIBP Meas on BP Alarm

• Trigger NIBP Meas on HR Alarm

• NIBP Auto Interval Default

• Adult Initial Cuff Inflation

• Pediatric Initial Cuff Inflation

• Neonatal Initial Cuff Inflation

• NIBP Patient Mode at Power Up

• NIBP Button Press & Hold

• Enable Motion Tolerance

Blood Pressure Units

This parameter allows you to set the NIBP unit of measurement.

Values are as follows:

Trigger NIBP Meas on BP Alarm

This parameter allows you to specify whether or not the R Series unit initiates a single

additional blood pressure measurement when any of the NIBP alarms trigger.

Values are as follows:

Trigger NIBP Meas on HR Alarm

This parameter allows you to specify whether or not the R Series unit initiates a single blood

pressure measurement when the heart rate/pulse rate alarm triggers.

Values are as follows:

Possible Values: mmHg (millimeters of mercury), kPa (kilopascals)

Default: mmHg

Possible Values: Yes, No

Default: Yes

Possible Values: Yes, No

Default: No

NIBP Settings (Optional)

9650-0902-05 Rev. C 45

NIBP Auto Interval Default

This parameter allows you to set the default for the amount of time between automatic

measurements.

Values are as follows:

Adult Initial Cuff Inflation

This parameter allows you to set the default NIBP cuff inflation pressure (the pressure to which

the NIBP cuff inflates at the beginning of its first measurement after power up).

Values are as follows:

Pediatric Initial Cuff Inflation

This parameter allows you to set the default pediatric NIBP cuff inflation pressure (the pressure

to which the NIBP cuff inflates at the beginning of its first measurement after power up, if set to

pediatric).

Values are as follows:

Neonatal Initial Cuff Inflation

This parameter allows you to set the default NIBP cuff inflation pressure (the pressure to which

the NIBP cuff inflates at the beginning of its first measurement after power up, if set to

neonatal).

Values are as follows:

Possible Values: 2.5, 3, 4, 5, 6, 7, 8, 9, 10, 15, 20, 30, 45, 60, 90, 120 minutes

Default: 30 minutes

Possible Values: mmHg: 120, 140, 160, 180, 200, 220, 240, 260

kPa: 16.0, 18.7, 21.3, 24.0, 26.7, 29.3, 32.0, 34.7

Default: mmHg: 160

kPa: 21.3

Possible Values: mmHg: 80, 90, 100, 110, 120, 130, 140, 150

kPa: 10.7, 12.0, 13.3, 14.7, 16.0, 17.3, 18.7, 20.0

Default: mmHg: 120

kPa: 16.0

Possible Values: mmHg: 60, 70, 80, 90, 100, 110, 120, 130

kPa: 8.0, 9.3, 10.7, 12.0, 13.3, 14.7, 16.0, 17.3

Default: mmHg: 90

kPa: 12.0

Chapter 2 Configuration Settings

46 9650-0902-05 Rev. C

NIBP Patient Mode at Power Up

This parameter allows you to set the default patient mode at power up.

Values are as follows:

NIBP Button Press & Hold

This parameter allows you to define which NIBP function is activated when the front panel

NIBP button ( ) is pressed and held for at least 2 seconds. You can configure the unit to

either:

• Begin a sequence of STAT measurements, or

• Begin taking NIBP measurements at repeating, selected intervals.

Values are as follows:

Enable Motion Tolerance

This parameter allows you enable compensation for motion tolerance, such as on a moving

stretcher.

Values are as follows:

Possible Values: Adult, Pediatric, Neonate

Default: Adult

Possible Values: Stat, Auto

Default: Stat

Possible Values: Yes, No

Default: No

EtCO2 Settings (Optional)

9650-0902-05 Rev. C 47

EtCO

Settings (Optional)

EtCO

configuration parameters are available for update only if the EtCO

monitoring option is

installed on the unit and include:

• Default EtCO2 Units

• Displayed Zoom Level

• Default EtCO2 Comp Setting

• Power Save Mode at Power Up

• EtCO

Average On Power Up

Default EtCO

Units

This parameter allows you to set the EtCO

unit of measurement.

Values are as follows:

Displayed Zoom Level

This parameter allows you to set the default scale setting for the displayed capnographic

waveform. It does not affect the printed waveform or the waveform data stored on the data

card.

Values are as follows:

Default EtCO

Comp Setting

This parameter allows you to set the default compensation for CO

Values are as follows:

Possible Values: mmHg (millimeters of mercury), kPa (kilopascals),% (percent)

Default: mmHg

Possible Values: mmHg: 0-12.5, 0-25, 0-50, 0-75, 0-100, 0-150

kPa: 0-1.7, 0-3.3, 0-6.6, 0-10.0, 0-13.3, 0-20.0

Default: mmHg: 0-50

kPa: 0-6.6

Possible Values: None, O2, N2O, O2 & N2O

Default: None

Chapter 2 Configuration Settings

48 9650-0902-05 Rev. C

Power Save Mode at Power Up

When this parameter is set to Yes, the unit automatically enters EtCO

power save mode when

powered on with a CAPNOSTAT sensor connected. The user must then enable the EtCO

device using the Param/EtCO2 softkey menu before use.

Values are as follows:

EtCO

Average On Power Up

This parameter sets the default time period over which the EtCO

values are averaged.

Values are as follows:

Possible Values: Yes, No

Default: Yes

Possible Values: 1 breath, 10 seconds, 20 seconds

Default: 10 seconds

Printer & Report Settings

9650-0902-05 Rev. C 49

Printer & Report Settings

The Printer and Report Config settings are attributes that control what and how things are

printed:

• Set Report Restart Delays

• Auto Generate Strips

• Print 3 Leads When Leads Sel.

Note: Printing is not available in AED mode.

Set Report Restart Delays

This setting allows you to review or change the length of time the device must be turned off

before it automatically erases all summary report and full disclosure data.

Values are as follows:

Auto Generate Strips

This setting allows you to set the strip chart recorder to automatically begin printing after a

defibrillator discharge or whenever alarms are triggered while in Manual mode.

Values are as follows:

Print 3 Leads When Leads Sel.

This setting allows you to specify whether or not the strip chart recorder prints three (3)

simultaneous leads of the patient ECG when Leads are selected and a 5- lead cable is in use.

Values are as follows:

Possible Values: 5 Min, 15 Min, 30 Min, 90 Min, 6 Hours, 1.5 Days, Manual

Default: 90 Min

Possible Values: Yes, No

Default: Yes

Possible Values: Yes, No

Default: No

Chapter 2 Configuration Settings

50 9650-0902-05 Rev. C

Readiness Test Settings

The Readiness Test settings are attributes that control how and when the R Series unit is self-

tested. It includes the following settings:

• Automatic Readiness Test

• Readiness Test Time

• Print Readiness Test Results

• Enable Readiness Test Audible Alert (Future Use)

• One Step Padz Installed

Automatic Readiness Test

This setting allows you to specify whether the R Series unit performs the automatic device

check.

Values are as follows:

Readiness Test Time

This setting allows you to specify what time the R Series unit performs the automatic device

check, if Automatic Device Check is set to Once a Day.

Values are as follows:

Print Readiness Test Results

This setting allows you to specify whether the R Series unit prints the results of the automatic

device check at the completion of the check, if Automatic Device Check is set to Once a Day. If

you want the unit to print results only when a failure is detected during the device check, set

this setting to Only If Fail.

Values are as follows:

Possible Values: Off, Once a Day

Default: Once a Day

Possible Values: 12:00 am, 1:00 am, 2:00 am, 3:00 am, 4:00 am, 5:00 am

Default: 12:00 am

Possible Values: Yes, No, Only if Fail

Default: Yes

Readiness Test Settings

9650-0902-05 Rev. C 51

Enable Readiness Test Audible Alert (Future Use)

This setting allows you to specify whether the unit emits a beep when the automatic device

check fails.

Values are as follows:

One Step Padz Installed

This setting allows you to specify whether the R Series unit tests the R Series OneStep

electrodes as part of the readiness test check, and which electrodes it tests.

• If this setting is set to any of its values (including No or Base), and CPR, MwP or Complete

electrodes are detected, they will be tested and the resulting status (pass/fail) is included in

the readiness result.

• If this setting is set to CPR/MwP/Complete, and none of these OneStep electrodes are

connected, or if the cable is not connected to the unit, the readiness result will indicate a

failure (Electrode: Not Connected).

• If this setting is set to Base or No, and the cable is correctly connected to a short (Base

electrode package, test port, or paddles in the wells), the unit will perform the readiness test

and not fail based on electrode type.

Values are as follows:

Note: The OneStep Padz Installed option should be set to Base unless you are using OneStep

electrodes marked Rev. B or above:

8900-0212-XX Rev. B or above for OneStep Pacing

8900-0213-XX Rev. B or above for OneStep CPR

8900-0214-XX Rev. B or above for OneStep Complete

Possible Values: No

Default: No

Possible Values: CPR/MwP/Complete, No, Base

Default: CPR/MwP/Complete

Chapter 2 Configuration Settings

52 9650-0902-05 Rev. C

AED Mode

The AED parameters are attributes that affect functions related to performing defibrillation

with an R Series unit in AED mode and include:

• Display ECG in AED Mode

• Display HR in AED Mode

• Manual Confirm Enable

• Extra CPR Interval Before 1st Analysis

• Duration of Extra CPR Interval

• Display Remaining CPR Timer

Display ECG in AED Mode

This parameter allows you to set the unit to either display or not display the patient’s ECG trace

on the monitor while in AED mode.

Values are as follows:

Display HR in AED Mode

This parameter allows you to set the unit to display the patient heart rate on the monitor while

in AED mode.

Values are as follows:

Manual Confirm Enable

This parameter allows you to set a confirmation key to enter Manual mode.

Values are as follows:

Possible Values: Yes, No

Default: Yes

Possible Values: Yes, No

Default: No

Possible Values: Yes, No

Default: Yes

AED Mode

9650-0902-05 Rev. C 53

Extra CPR Interval Before 1st Analysis

This parameter pertains only to AED mode.

When this parameter is set to No (default), and the unit detects a pad connection upon power-

on, it automatically starts an ECG analysis. If the unit is powered on with no pads connected,

the unit displays the ATTACH PADS prompt until pads are connected. Once pads are connected,

the unit automatically starts an ECG analysis.

When this parameter is set to Yes, the unit displays the prompts: CHECK PULSE for 10

seconds, then IF NO PULSE, PERFORM CPR for the configured Extra CPR interval at power

on. At the end of the CPR period, if the unit does not detect a pads connection, it displays the

prompt ATTACH PADS until pads are connected. If a pads connection is detected, the unit

automatically starts an ECG analysis. You can start an ECG analysis during the CPR interval by

pressing the ANALYZE softkey.

Values are as follows:

Duration of Extra CPR Interval

This parameter allows you to specify the duration of the extra CPR interval (see previous

entry). It has no effect if “Extra CPR Interval Before 1st Analysis” is set to No.

Values are as follows:

Display Remaining CPR Timer

This parameter allows you to specify whether to display remaining CPR interval during CPR.

Values are as follows:

Possible Values: Yes, No

Default: No

Possible Values: 0.5, 1, 1.5, 2, 2.5, 3, 3.5 or 4 minutes

Default: 2 minutes

Possible Values: Yes, No

Default: Yes

Chapter 2 Configuration Settings

54 9650-0902-05 Rev. C

Wi-Fi Settings (Optional)

The Wi-Fi settings are attributes that control how files are transferred and the security method

that is used.

Full Disclosure Transfer Mode

This setting allows you to determine the following:

• whether full disclosure file transfers are supported

• whether the Send Report softkey is displayed

Values are as follows:

Defib History Transfer Mode

This setting allows you to specify whether device check files and activity log files will be

transmitted, and determines whether Defib History to Wi-Fi softkey is displayed.

Values are as follows:

Infrastructure Mode Options

DHCP/Static IP

This setting allows you to either manually set the static IP address or retrieve the IP address

from a DHCP server.

Note: If this setting is set to Static IP, you need to set the following settings: Gateway IP

Address, Subnet Mask, and DNS IP Address.

Values are as follows:

Possible Values: Server, None

Default: Server

Possible Values: Both, None, Manual, Automatic

Default: None

Possible Values: Static IP, DHCP

Default: DHCP

Wi-Fi Settings (Optional)

9650-0902-05 Rev. C 55

Local IP Address

This setting allows you to specify the defibrillator’s IP address used in the static configuration.

Note: This setting is available only when DHCP/Static IP is set to Static IP.

Values are as follows:

Procedure

Follow these steps to set up a Local IP Address.

Possible Values: XXX.XXX.XXX.XXX where XXX is 000 to 255

Default: 192.168.100.100

Step Action

1. From the Select Configuration Categories screen,

select Wi-Fi, then press the Enter softkey.

The Wi-Fi Configuration screen appears.

2. Press the Next Item softkey until Local IP

Address appears and press the Change Value

softkey.

The Set Local IP Address screen appears.

3. Use the softkey as follows:

•

 — moves the highlight left and right

through the character selection table.

• Enter Char — enters the highlighted

character for each digit of the IP address.

• Return — returns you to the Wi-Fi

Configuration screen. Press the Return

softkey when you are finished entering the

address.

Item

System Configuration

Wi-Fi Configuration

Defib History

Transfer Mode

DHCP/

Static IP

Both

Static IP

Main

Exit

Config

Category

List

Change

Value

Full Disclosure

Transfer Mode

Server

Page 1 of 7

System Configuration

Set Local IP Address

192.168.100.100

Return

Enter

Char

Cancel

Chapter 2 Configuration Settings

56 9650-0902-05 Rev. C

Gateway IP Address

This setting allows you to specify the router’s IP used in the static configuration.

Note: This setting is accessible only when DHCP/Static IP is set to Static IP.

Values are as follows:

Procedure

Follow these steps to set up a Gateway IP Address.

Possible Values: XXX.XXX.XXX.XXX where XXX is 000 to 255

Default: 192.168.100.001

Step Action

1. From the Select Configuration Categories screen,

select Wi-Fi, then press the Enter softkey.

The Wi-Fi Configuration screen appears.

2. Press the Next Item softkey until Gateway IP

Address appears and press the Change Value

softkey.

The Set Gateway IP Address screen appears.

3. Use the softkey as follows:

•

 — moves the highlight left and right

through the character selection table.

• Enter Char — enters the highlighted

character for each digit of the IP address.

• Return — returns you to the Wi-Fi

Configuration screen. Press the Return

softkey when you are finished entering the

address.

Item

System Configuration

Wi-Fi Configuration

Defib History

Transfer Mode

DHCP/

Static IP

Both

Static IP

Main

Exit

Config

Category

List

Change

Value

Full Disclosure

Transfer Mode

Server

Page 1 of 7

System Configuration

Set Gateway IP Address

192.168.100.001

Return

Enter

Char

Cancel

Wi-Fi Settings (Optional)

9650-0902-05 Rev. C 57

Subnet Mask

This setting allows you to specify the subnet mask used in the static configuration.

Note: This setting is accessible only when DHCP/Static IP is set to Static IP.

Values are as follows:

Procedure

Follow these steps to set up a subnet mask.

Possible Values: XXX.XXX.XXX.XXX where XXX is 000 to 255

Default: 255.255.255.000

Step Action

1. From the Select Configuration Categories screen,

select Wi-Fi, then press the Enter softkey.

The Wi-Fi Configuration screen appears.

2. Press the Next Item softkey until Subnet Mask

appears and press the Change Value softkey.

The Set Subnet Mask screen appears.

3. Use the softkey as follows:

•

 — moves the highlight left and right

through the character selection table.

• Enter Char — enters the highlighted

character for each digit of the subnet mask.

• Return — returns you to the Wi-Fi

Configuration screen. Press the Return

softkey when you are finished entering the

subnet mask.

Item

System Configuration

Wi-Fi Configuration

Defib History

Transfer Mode

DHCP/

Static IP

Both

Static IP

Main

Exit

Config

Category

List

Change

Value

Full Disclosure

Transfer Mode

Server

Page 1 of 7

System Configuration

Set Subnet Mask

255.255.255.000

Return

Enter

Char

Cancel

Chapter 2 Configuration Settings

58 9650-0902-05 Rev. C

Use DNS

This setting allows you to specify whether to use a DNS to obtain the server IP address from the

server name.

Values are as follows:

Primary/Secondary DNS IP Address

This setting allows you to specify the Primary and Secondary IP address of the DNS server to

use if the following conditions are met:

• Use DNS setting is set to Yes

• DHCP/Static IP setting is set to Static IP

Values are as follows:

Procedure

Follow these steps to set up a Primary DNS IP Address.

Possible Values: Yes, No

Default: Yes

Possible Values: XXX.XXX.XXX.XXX where XXX is 000 to 255

Default: 192.168.100.2

Step Action

1. From the Select Configuration Categories screen,

select Wi-Fi, then press the Enter softkey.

The Wi-Fi Configuration screen appears.

2. Press the Next Item softkey until the

Primary DNS IP Address appears and press the

Change Value softkey.

The Set Primary DNS IP Address screen

appears.

Item

System Configuration

Wi-Fi Configuration

Defib History

Transfer Mode

DHCP/

Static IP

Both

Static IP

Main

Exit

Config

Category

List

Change

Value

Full Disclosure

Transfer Mode

Server

Page 1 of 7

System Configuration

Set Primary DNS IP Address

1 9 2 . 1 6 8 . 1 0 0 . 2

Return

Enter

Char

Cancel

Wi-Fi Settings (Optional)

9650-0902-05 Rev. C 59

Follow the same steps to enter a Secondary DNS IP address.

SSID Names (up to 2 entries)

This setting allows you to specify the specific SSID string. You can specify up to 2 entries with

a 32 character limit.

Allowable characters:

A-Z, a-z, 0-9

,@.-_':`%&(){}/|*=^~< >

space

Procedure

Follow these steps to set up an SSID name(s).

3. Use the softkey as follows:

•

 — moves the highlight left and right

through the character selection table.

• Enter Char — enters the highlighted

character for each digit of the IP address.

• Return — returns you to the Wi-Fi

Configuration screen. Press the Return

softkey when you are finished entering the

address.

Step Action

1. From the Select Configuration Categories screen,

select Wi-Fi, then press the Enter softkey.

The Wi-Fi Configuration screen appears.

2. Press the Next Item softkey until SSID NAMES

appears and press the Change Value softkey.

The Set SSID screen appears.

Item

System Configuration

Wi-Fi Configuration

Defib History

Transfer Mode

DHCP/

Static IP

Both

Static IP

Main

Exit

Config

Category

List

Change

Value

Full Disclosure

Transfer Mode

Server

Page 1 of 7

System Configuration

Set SSID

1 : s e r v e r 0 0 1

2 :

;

‘

“

Cancel

Return

Enter

Char

Del

...

Chapter 2 Configuration Settings

60 9650-0902-05 Rev. C

Server Name (Full Disclosure)

This setting allows you to specify the server name string to use (up to 255 characters) if the

following conditions are met:

• Use DNS setting is set to Yes

• Full Disclosure Transfer Mode is not set to Server

Allowable characters:

A-Z, a-z, 0-9

-. (hyphen, period)

Procedure

Follow these steps to set up a server name.

3. In the character selection table:

•

 moves the cursor to the next line.

• . . . — changes the table to a different set of

characters, including uppercase letters.

Use the softkeys as follows:

•

 — moves the highlight up, down,

left, and right through the character selection

table.

• Enter Char — enters the highlighted

character for each digit of the SSIDs.

• Return — returns you to the Wi-Fi

Configuration screen. Press the Return

softkey when you are finished entering the

ID(s).

Step Action

1. From the Select Configuration Categories screen,

select Wi-Fi, then press the Enter softkey.

The Wi-Fi Configuration screen appears.

Item

System Configuration

Wi-Fi Configuration

Defib History

Transfer Mode

DHCP/

Static IP

Both

Static IP

Main

Exit

Config

Category

List

Change

Value

Full Disclosure

Transfer Mode

Server

Page 1 of 7

Wi-Fi Settings (Optional)

9650-0902-05 Rev. C 61

Server IP (Full Disclosure)

This setting allows you to specify the server IP address to use if the following conditions are

met:

• Use DNS is set to No

• Full Disclosure Transfer Mode is set to Server

Values are as follows:

2. Press the Next Item softkey until Server Name

(Full Disclosure) appears and press the Change

Value softkey.

The Set Server Name (Full Disclosure) screen

appears.

3. In the character selection table:

•  moves the cursor to the next line.

• . . . — changes the table to a different set of

characters, including uppercase letters.

Use the softkeys as follows:

•  — moves the highlight up, down,

left, and right through the character selection

table.

• Enter Char — enters the highlighted

characters of the server name.

• Return — returns you to the Wi-Fi

Configuration screen. Press the Return

softkey when you are finished entering the

server name.

Step Action

System Configuration

Set Server Name (Full Disclosure)

Z O L L D N S

;

‘

“

Cancel

Return

Enter

Char

Del

...

Possible Values: XXX.XXX.XXX.XXX where XXX is 0 to 255

Default: 000.000.000.000

Chapter 2 Configuration Settings

62 9650-0902-05 Rev. C

Procedure

Follow these steps to set up a server IP address.

Server Port (Full Disclosure)

This setting allows you to specify the TCP port used to connect with the server if the Full

Disclosure Transfer Mode setting is set to Server.

Values are as follows:

Step Action

1. From the Select Configuration Categories screen,

select Wi-Fi, then press the Enter softkey.

The Wi-Fi Settings screen appears.

2. Press the Next Item softkey until Server IP (Full

Disclosure) appears and press the Change

Value softkey.

The Set Full Disc. Server IP Address screen

appears.

3. Use the softkey as follows:

•

 — moves the highlight up, down,

left, and right through the character selection

table.

• Enter Char — enters the highlighted

character for each digit of the server IP

address.

• Return — returns you to the Wi-Fi

Configuration screen. Press the Return

softkey when you are finished entering the IP

address.

Item

System Configuration

Wi-Fi Configuration

Defib History

Transfer Mode

DHCP/

Static IP

Both

Static IP

Main

Exit

Config

Category

List

Change

Value

Full Disclosure

Transfer Mode

Server

Page 1 of 7

System Configuration

Set Full Disc. Server IP Address

192.168.042.001

Return

Enter

Char

Cancel

Default: 11000

Wi-Fi Settings (Optional)

9650-0902-05 Rev. C 63

Procedure

Follow these steps to set up a server port name.

Server Name (Defib History)

This setting allows you to specify the server name string to use (up to 255 characters) if the

following conditions are met:

• Use DNS is set to Yes

• Defib History Transfer Mode is not set to None

Allowable characters:

A-Z, a-z, 0-9

-. (hyphen, period)

Step Action

1. From the Select Configuration Categories screen,

select Wi-Fi, then press the Enter softkey.

The Wi-Fi Settings screen appears.

2. Press the Next Item softkey until Set Server Port

(Full Disclosure) appears and press the Change

Value softkey.

The Set Full Disc. Server Port screen appears.

3. Use the softkey as follows:

•

 — moves the highlight up, down,

left, and right through the character selection

table.

• Enter Char — enters the highlighted

character for each digit of the port.

• Return — returns you to the Wi-Fi

Configuration screen. Press the Return

softkey when you are finished entering the

server port name.

Item

System Configuration

Wi-Fi Configuration

Defib History

Transfer Mode

DHCP/

Static IP

Both

Static IP

Main

Exit

Config

Category

List

Change

Value

Full Disclosure

Transfer Mode

Server

Page 1 of 7

System Configuration

Set Full Disc. Server Port

1 1 0 0 0

Return

Enter

Char

Cancel

Chapter 2 Configuration Settings

64 9650-0902-05 Rev. C

Procedure

Follow these steps to set up a server name.

Server IP (Defib History)

This setting allows you to specify the server IP address to use if the following conditions are

met:

• Use DNS is set to No

• Defib History Transfer Mode is not set to None

Step Action

1. From the Select Configuration Categories screen,

select Wi-Fi, then press the Enter softkey.

The Wi-Fi Settings screen appears.

2. Press the Next Item softkey until Server Name

(Defib History) appears and press the Change

Value softkey.

The Set Server Name (Defib History) screen

appears.

3. In the character selection table:

•  moves the cursor to the next line.

• . . . — changes the table to a different set of

characters, including uppercase letters.

Use the softkeys as follows:

•  — moves the highlight up, down,

left, and right through the character selection

table.

• Enter Char — enters the highlighted

characters of the server name.

• Return — returns you to the Wi-Fi

Configuration screen. Press the Return

softkey when you are finished entering the

server name.

Item

System Configuration

Wi-Fi Configuration

Defib History

Transfer Mode

DHCP/

Static IP

Both

Static IP

Main

Exit

Config

Category

List

Change

Value

Full Disclosure

Transfer Mode

Server

Page 1 of 7

System Configuration

Set Server Name (Defib History)

Z O L L D N S

;

‘

“

Cancel

Return

Enter

Char

Del

...

Wi-Fi Settings (Optional)

9650-0902-05 Rev. C 65

Values are as follows:

Procedure

Follow these steps to set up an server IP address.

Possible Values: XXX.XXX.XXX.XXX where XXX is 0 to 255

Default: 000.000.000.000

Step Action

1. From the Select Configuration Categories screen,

select Wi-Fi, then press the Enter softkey.

The Wi-Fi Settings screen appears.

2. Press the Next Item softkey until Server IP (Defib

History) appears and press the Change Value

softkey.

The Set Defib History Server IP Address screen

appears.

3. Use the softkey as follows:

•

 — moves the highlight up, down,

left, and right through the character selection

table.

• Enter Char — enters the highlighted

character for each digit of the server IP.

• Return — returns you to the Wi-Fi

Configuration screen. Press the Return

softkey when you are finished entering the

server IP.

Item

System Configuration

Wi-Fi Configuration

Defib History

Transfer Mode

DHCP/

Static IP

Both

Static IP

Main

Exit

Config

Category

List

Change

Value

Full Disclosure

Transfer Mode

Server

Page 1 of 7

System Configuration

Set Defib History Server IP Address

192.168.042.001

Return

Enter

Char

Cancel

Chapter 2 Configuration Settings

66 9650-0902-05 Rev. C

Server Port (Defib History)

This setting allows you to specify the TCP port used to connect with the server if Defib History

Transfer Mode is not set to None.

Values are as follows:

Procedure

Follow these steps to set up a server port.

Default: 11000

Step Action

1. From the Select Configuration Categories screen,

select Wi-Fi, then press the Enter softkey.

The Wi-Fi Settings screen appears.

2. Press the Next Item softkey until Set Server Port

(Defib History) appears and press the Change

Value softkey.

The Set Defib History Server Port screen

appears.

3. Use the softkey as follows:

•

 — moves the highlight up, down,

left, and right through the character selection

table.

• Enter Char — enters the highlighted

character for each digit of the server port.

• Return — returns you to the Wi-Fi

Configuration screen. Press the Return

softkey when you are finished entering the

server port.

Item

System Configuration

Wi-Fi Configuration

Defib History

Transfer Mode

DHCP/

Static IP

Both

Static IP

Main

Exit

Config

Category

List

Change

Value

Full Disclosure

Transfer Mode

Server

Page 1 of 7

System Configuration

Set Defib History Server Port

1 1 0 0 0

Return

Enter

Char

Cancel

Wi-Fi Settings (Optional)

9650-0902-05 Rev. C 67

Passphrase/Keys (up to 2 entries)

This setting allows you to specify the Wi-Fi passphrase. The ... key allows you to select upper

case letters and other symbols. You can specify up to 2 entries with a 63-character limit.

Procedure

Follow these steps to set up a passphrase.

Step Action

1. From the Select Configuration Categories screen,

select Wi-Fi, then press the Enter softkey.

The Wi-Fi Settings screen appears.

2. Press the Next Item softkey until Passphrase/

Keys (up to 2 entries) appears and press the

Change Value softkey.

3. The Set Passphrase/Key screen appears.

Use the softkey as follows:

•

 — moves the highlight up, down,

left, and right through the character selection

table.

• Enter Char — enters the highlighted

character for each character of the

passphrase/key.

• Return — returns you to the Wi-Fi

Configuration screen. Press the Return

softkey when you are finished entering the

passphrase(s).

Item

System Configuration

Wi-Fi Configuration

Defib History

Transfer Mode

DHCP/

Static IP

Both

Static IP

Main

Exit

Config

Category

List

Change

Value

Full Disclosure

Transfer Mode

Server

Page 1 of 7

Item

System Configuration

Wi-Fi Configuration

Enable Report ID

Yes

Main

Exit

Config

Category

List

Change

Value

SSID Names

(up to 2 entries)

Set/Review

Page 6 of 7

Passphrase/Keys

(up to 2 entries)

Set/Review

System Configuration

Set Passphrase/Key

1: S e c r e t C o d e

;

‘

“

Cancel

Return

Enter

Char

Del

...

Chapter 2 Configuration Settings

68 9650-0902-05 Rev. C

Wi-Fi Transmission Mode Options

Enable Report ID

This setting allows you to enable or disable the option to enter a unique alphanumeric patient

ID before Wi-Fi transmission of a Full Disclosure report. If set to No, the report will be sent

automatically.

Values are as follows:

Wi-Fi Region

This setting allows you to specify the Wi-Fi domain (United States, Japan, or Europe).

Values are as follows:

Wi-Fi Radio

This setting allows you to specify the Wi-Fi radio 802.11 standard.

Values are as follows:

Possible Values: Yes, No

Default: No

Possible Values: US, EU, JP

Default: US

Possible Values: b/g/n (2.4GHz), a/n (5GHz)

Default: b/g/n (2.4GHz)